; Tables and Values Having to do with MAP
;----------------------------------------
;{B0101} Main VE Table
;{B0102} VE While Cranking
;{B3310} DFCO M6 MAP
;{B3321} DFCO MAP Hysteresis
;{B3320} DFCO MAP
;{B3613} PE MAP Threshold
;{B3623} Hot PE Mode MAP Threshold (Entry)
;{B3624} Hot PE Mode MAP Threshold (Exit)
;{B3605} EQ Ratio When in Open Loop
;{B3701} Injector Pulse Width Voltage Adjustment
;{B3810) MAP Boundries for LTFT Cells
;{B0303} MAP Fail Default Baro
;{B5913} Spark High-Octane Table
;{B5914} Spark Low-Octane Table
;{B6213} Adaptive Spark Min MAP
;{B6204} Knock Retard Limit Not in PE Mode
;{B6206} Knock Retard Default Value with Knock DTC
;{C2911} MAF Rationality test
;{C5501} MAP Rationality Test RPM High
;{C5502} MAP Rationality Test RPM Low
;{C6301} MAP Sensor Scaler
;{C6302} MAP Sensor Offset
;{C3904} TPS Test Min MAP
;{C3905} TPS Test Max MAP

; Tables and values having to do with BARO
;-----------------------------------------
;{B3314} DFCO Vehical Speed Enable
;{B0301} Min RPM for Barometer Update
;{B0302} Max RPM for Barometer Update
;{B0303} MAP Fail Default Baro
;{B0304} Baro Offset Factor

; Tables to be modified by hand
;----------------------------------------
;{B5913} This table must be hand modified until support for updating tables from tun tables is supported
;{B5914} - ditto above
;{C2911} MAF Rationality test - what is rational for 2bar?
;{C5501} fixing this might fix DTC P0106 ???
;{C5502} - ditto above

; NOTES - Don kno much about history...
;-----------------------------------------
; B0304 Baro Offset Factor - Is this tied into the MAF?
; At some point you will need to rescale your LTFT matrix etc to suit the halved kPa value,
;  B3809 RPM Boundries for LTFT Cells - This is weird. 2500, 6502,6503???  Shouldnt they be more linear?
;  B3810 MAP Boundries for LTFT Cells - where should the boundries lie for 2bar?

[Script]
;ID	Cal	Adj	Value	Update Area		Comments
;------	-------	-------	-------	-----------------------	------------------------------
;10=	B0101	PCT	-50	.			copy column 30 to 15, 40 to 20, 50 to 25... etc. 105kPa + ???
;20=	B0102						??? what to do here? same as B0101?
30=	B3310	PCT	-50	.			Decrease value by 50%.
40=	B3321	PCT	-50	.			Decrease value by 50%.
;50=	B3320						???? confused
60=	B3613	PCT	-50	.			Decrease value by 50%.
70=	B3623	PCT	-50	.			Decrease value by 50%.
80=	B3624	PCT	-50	.			Decrease value by 50%.
;90=	B3605						??? what to do here? same as B0101?
;100=	B3701						??? BAH!
160=	B0301	SET	9500	.			Effectively disable baro update.
160=	B0302	SET	9600	.			Effectively disable baro update.
120=	B0303	PCT	-50	.			Decrease value by 50%.
110=	B3810	PCT	-50	.			Decrease table by 50%.
120=	B0304	SET	1.00	.			Set to 1.00
130=	B6213	PCT	-50	.			Decrease value by 50%.
;140=	B6204						??? what to do here? same as B0101?
;150=	B6206						??? what to do here? same as B0101?
160=	C6301	SET	128	.			Set the scalar value.
170=	C6302	PCT	-50	.			Decrease value by 50%.
180=	C3904	PCT	-50	.			Decrease value by 50%.
190=	C3905	PCT	-50	.			Decrease value by 50%.
200=	C6101	PCT	$PR	.			(formula) PR = (14.7 - boost psi) / 14.7 

500=	C6001	SET	C6001	.			Set DTC to values in Section C6001 below
510=	C6002	SET	C6002	.			Set DTC to values in Section C6002 below


[C6001]
;0 = A: 1 Trip, Emissions Related
;1 = B: 2 Trips, Emissions Related
;2 = C: Non Emissions
;3 = X: Not Reported
;DTC	Value
;------	---------------------------------------------------------------------
P0102= 2
P0106= 3
P0107= 3
P0108= 3


[C6002]
;0 = No Mil
;1 = Mil
;DTC	Value
;------	---------------------------------------------------------------------
P0102= 0
P0106= 0
P0107= 0
P0108= 0